Build Score Summary: This is a much more aggressive setup than a conventional 22×8 Cutlass build. The staggered wheel position, deep rear dish, slightly wider rear tire, and shortened rear end work together to give the 1984 Cutlass Supreme a true custom stance while maintaining very similar front and rear tire diameters.
22×8 Staggered Wire Wheels on a 1984 Cutlass Supreme
The 1984 Oldsmobile Cutlass Supreme is one of the classic G-body platforms that responds especially well to a staggered wheel setup.
Napoleon Rodriguez’s Cutlass uses 22×8 150-spoke wire wheels, but the front and rear wheel positions are deliberately different.
The front maintains a cleaner, shallower wheel profile, while the rear uses a deep-dish configuration designed to create a significantly larger visible lip.
This gives the car the classic staggered effect:
Cleaner Front + Aggressive Deep Rear
Rather than making all four wheels identical, the staggered setup adds visual width and depth to the rear of the vehicle.
Deep-Dish Rear Wire Wheel Setup
The rear wheel is the centerpiece of this build.
A deep-dish wire wheel changes the wheel geometry so that considerably more of the wheel lip becomes visible from the outside.
That look is especially effective on a classic rear-wheel-drive Cutlass because it emphasizes the rear quarters and gives the vehicle a more aggressive custom stance.
However, achieving a true deep rear dish requires more than simply installing a different wheel.
Why the Rear End Must Be Shortened
For this type of deep-dish rear setup, shortening the rear end is required.
The factory rear axle places the wheel-mounting surfaces at a fixed width. With a conventional standard wheel, that works because the wheel is designed around the factory axle position.
A deep-dish wheel changes where the wheel sits relative to that mounting surface.
To create a significantly deeper outer lip without pushing the entire wheel excessively outside the rear quarter panel, the axle mounting surfaces need to move inward.
That is accomplished by narrowing or shortening the rear end.
In simple terms:
Factory-Width Rear End
Works well with a more standard wheel position.
Shortened Rear End
Allows the wheel to move inward so a deeper rear lip can sit properly beneath the body.
This is why shortening the rear end is not merely cosmetic—it is part of creating the correct geometry for an aggressive deep-dish stance.
How Much Should the Rear End Be Shortened?
There is no universal shortening measurement that should be applied to every Cutlass.
The exact amount depends on:
- Desired rear lip depth
- Wheel backspacing
- Wheel offset
- Actual axle width
- Rear brake setup
- Inner wheel-well clearance
- Outer quarter-panel clearance
- Suspension configuration
- Tire width
The rear end should therefore be measured and shortened around the actual wheel specifications and desired final stance.
I would include this prominently:
Deep-Dish Fitment Note: This staggered build requires a shortened rear end to properly position the deep-dish rear wheels. The exact amount of narrowing should be determined from the actual wheel backspacing, axle width, tire size, and available inner and outer clearance before fabrication.
245/30R22 Front + 255/30R22 Rear
The tire sizing is another very smart part of this staggered setup.
Napoleon’s Cutlass uses:
Front
245/30R22 Red Stripe Tires
Rear
255/30R22 Red Stripe Tires
The rear tire is slightly wider, reinforcing the staggered stance without creating a major difference in overall tire height.
Staggered Tire Size Comparison
| Specification | Front | Rear |
|---|---|---|
| Tire Size | 245/30R22 | 255/30R22 |
| Section Width | 245 mm | 255 mm |
| Sidewall Height | ≈ 2.89″ | ≈ 3.01″ |
| Overall Diameter | ≈ 27.8″ | ≈ 28.0″ |
| Width Difference | — | 10 mm wider |
| Diameter Difference | — | ≈ 0.24″ taller |
This is an excellent staggered combination because the rear tire gets additional width without becoming dramatically taller than the front.
Why the Front and Rear Tire Diameters Matter
On a staggered setup, you generally do not want a huge difference in overall tire height unless the vehicle is specifically engineered for it.
Here, the approximate diameters are:
245/30R22 front: 27.8 inches
255/30R22 rear: 28.0 inches
That is only around 0.24 inch of total diameter difference.
Visually, the tires remain nearly the same height, while the rear gains a little additional width and sidewall.
That means the staggered appearance comes primarily from:
the deeper rear wheel dish and wider rear tire, rather than from making the rear tire dramatically taller.
That is exactly what you want on this type of Cutlass build.
Why Not Use 265/35R22?
A 265/35R22 would be significantly taller than either tire used here.
It measures approximately 29.3 inches overall, compared with approximately 27.8–28.0 inches for Napoleon’s staggered setup.
That additional tire height dramatically reduces clearance around the wheel opening and suspension.
For a low, deep-dish Cutlass build, a 265/35R22 can work against the goal of keeping the wheel tucked properly beneath the body.
The lower-profile 245/30R22 front and 255/30R22 rear combination is far better suited to this type of aggressive staggered stance because it keeps overall diameter under control.
Standard 22s vs. Deep-Dish Staggered 22s
This is an important distinction for customers.
| Setup | Standard 22×8 | Staggered Deep-Dish 22×8 |
|---|---|---|
| Front Wheel | Standard | Standard / Shallower |
| Rear Wheel | Standard | Deep Dish |
| Rear-End Shortening | Generally not part of the standard configuration | Required |
| Visual Rear Lip | Moderate | Deep / Aggressive |
| Fabrication | Lower | Higher |
| Fitment Complexity | Lower | Significantly Higher |
| Appearance | Clean 22-inch stance | Custom staggered stance |
| Best For | Straightforward large-wheel build | Maximum rear-dish appearance |
For customers who simply want a clean 22-inch Cutlass, a standard wheel configuration is much easier.
For customers specifically chasing the deep rear dish, the shortened rear end becomes part of the build.
Why This Setup Works on the 1984 Cutlass Supreme
The G-body Cutlass has strong rear-quarter proportions that visually support a staggered wheel package particularly well.
The front remains clean, while the deep rear wheel creates the impression of a wider and more aggressive rear stance.
The strongest parts of Napoleon’s setup are:
- 22×8 wire-wheel sizing
- Dense 150-spoke design
- Staggered front and rear wheel profile
- Deep-dish rear appearance
- Shortened rear end for proper wheel positioning
- 245/30R22 front tire
- Wider 255/30R22 rear tire
- Nearly matching front and rear tire diameters
- Red Stripe tire accents
- Aggressive classic G-body stance
Build Highlights & Fitment Notes
| Build Highlights | Fitment & Ownership Notes |
|---|---|
| 22×8 150-spoke wire wheels | Custom vehicle-specific fitment required |
| Staggered setup | Front and rear wheel geometry differ |
| Deep-dish rear wheels | Rear-end shortening required |
| 245/30R22 front | Approx. 27.8″ overall diameter |
| 255/30R22 rear | Approx. 28.0″ overall diameter |
| Red Stripe tires | Rear tire is 10 mm wider than front |
| Aggressive rear stance | Inner and outer rear clearance must be measured |
| G-body custom fitment | Professional fabrication and installation recommended |
Important Rear Clearance Considerations
Shortening the rear end creates additional room for the deep-dish wheel, but all clearances still need to be checked after fabrication.
Important areas include:
Inner wheel well
Frame and suspension components
Outer quarter panel
Brake components
Tire clearance under suspension compression
A deep wheel can have adequate outer clearance but still interfere on the inside if the backspacing is incorrect.
That is why this type of build should be measured around the exact finished wheel specifications rather than relying solely on generic vehicle fitment data.
Looking for Staggered 22-Inch Wire Wheels for an Oldsmobile Cutlass Supreme?
Ninja Tire offers 22-inch wire wheels, staggered configurations, custom deep-dish rear wheels, and complete wheel-and-tire packages for classic Oldsmobile Cutlass Supreme builds.
For customers wanting a straightforward setup, a standard 22×8 wheel configuration is considerably easier to install.
For customers seeking the aggressive look of a deep rear dish, the setup requires more planning. The rear axle must be shortened so the deeper wheel can move inward and sit correctly beneath the rear quarter panel.
Napoleon’s setup combines 245/30R22 front tires with 255/30R22 rear tires, providing additional rear width while keeping the overall tire diameters extremely close.
Explore related Ninja Tire options:











